DIY? Or Call TDC? ... How To Replace Your Door Threshold

[This week in our series "DIY? Or call TDC?" we're covering the replacement of a door threshold. This project and others in this series are tasks you can do yourself for your business. Don't have time? Need parts or assistance? You can always call The Door Company at (614) 338-1414.]

Here are 4 simple steps that will help you quickly and easily replace a door threshold.

Step 1 – Prepare before Buying Your New Threshold Strip

In purchasing a new door threshold you'll need to know which sizes will best fit the door. Measure each door separately. All doors do not necessarily have the same dimensions. You'll need two measurements for each door: the width of the doorway—not the door, itself, and the gap between the floor and the bottom edge of the door. Examine the space between your door and the floor below it to determine what has created this space. Was the threshold not high enough? Is the threshold the right size, but is now worn down or broken off?  Has the concrete or other flooring been damaged under the threshold? Has the threshold been damaged by snow melt compounds?

Step 2 – Choose from Available Types

You'll find a large variety of thresholds on the market.  Most are made of aluminum and may or may not have lips with some type of gasketing material that helps provide a seal for the door against weather.

Be sure to check the measurement of the threshold you purchase, to ensure that it matches the type you'll need to fill the gap between the door bottom edge and the floor beneath it. If you are unable to find a threshold long enough to match your opening, buy one that is longer, one you will be able to cut and fit to the opening.

Step 3 – Remove the Old Threshold

Locate the screws that attach the strip to the floor. If no screws are visible, and if you see a rubber or plastic strip in the center of the old thresold, use a flathead screwdriver to remove this strip. It's very likely that you'll find your screws in the channel the rubber strip occupied. Use your screwdriver to remove the screws that hold the old threshold to the floor.

Step 4 – Attach Your New Threshold  

If you need to shorten your new threshold, carefully measure and mark it. Then, cut it to length. Check to see if holes in the new threshold are aligned with screw holes in the floor. If they're not, use your drill and bit to drill new holes that will line up with the new holes. Then, attach the threshold with new screws.

We can solve any door problem you have. If you need parts for this project, give us a call at (614) 338-1414. Our headquarters at 3247 E. 11th Ave., Columbus, features a walk-in parts counter, and we can get you what you need!

Thank you for stopping by!

Like The Door Company on Facebook,
follow @TheDoorCo_ofOH on Twitter,
or add us to your Google+ Circles.

DIY? Or Call TDC? ... What To Do If A Door Doesn't Latch Properly

[This week in our series "DIY? Or call TDC?" we're discussing making sure your doors latch properly. This project and others in this series are tasks you can do yourself for your business. However, if you don't have time, need parts or run into problems, you can always call The Door Company at (614) 338-1414.]

Every door will have a time when it will not latch correctly. There may be different reasons why a door will not latch. Damp weather or heat may be warping the door. Ground that has frozen under the door may also cause the door not to close properly. Also, usual wear and tear can contribute to the door not latching properly. There are several ways to fix a door that will not latch.

Step 1- Check Hinges

If the door is not latching properly, the easiest place to start with is with the door hinges. When the hinges are loose the door will travel up and down while it is being opened and closed. If the door is sagging and will not line up with the latch, check the door hinges. Lift the door up to relieve the pressure on the hinges and tighten the screws. If the screws have been stripped, the screws will not tighten in the holes. In that case, take the hinges from the frame. Drill new holes that are slightly smaller than a wood dowel. Hammer in the dowel and cut off excess. Reinstall the hinges and attach the screws into the dowel.  For an emergency repair, a simple wood pencil can be used in place of a wood dowel.

Step 2- Check the Latch and Strike Plate

When you open the door you will see the latch on the door and the strike plate which is on the door jamb. Check both for loose screws. Tighten any screws that are lose and check the door again. If it latches securely then problem is solved. If not, then there is another problem.

Slide the latch in and out to see if it moves smoothly. If it doesn't, the door knob may be too tight. Loosen the knobs a little to relieve some of the pressure on the door and to free up the latch a little. If the latch is still catching in the door, apply WD-40 or silicone lubricant.

Step 3- Align Strike Plate

If the door still does not latch properly, then it could be that the strike plate is not aligning properly with the latch. Close the door and check to see if  the strike plate is too high or too low. Also check to see that it is aligning left and right. You can fix this problem in three different ways. For small adjustments, use a metal file on the strike plate to open it up a little more for the latch to set properly. You can also place a piece of wood in the strike plate and hammer the wood up or down to move the plate until it aligns.

The last plate repair suggestion is one that you can do easily. Simply unscrew the strike plate and reattach it at a different height--either lower or higher--depending upon how unaligned the plate was.

Need parts for this project? Give us a call at (614) 338-1414. Our headquarters at 3247 E. 11th Ave., Columbus, features a walk-in parts counter, and we can get you what you need!

Thank you for stopping by!

Like The Door Company on Facebook,
follow @TheDoorCo_ofOH on Twitter,
or add us to your Google+ Circles.

DIY? Or Call TDC? ... Installing a Door Sweep for your Business

[We're beginning a new series called "DIY? Or call TDC?" this week. These posts will consist of repair and/or maintenance procedures for your business. Many of these tasks, you can do yourself. However, if you don't have time, need parts or run into problems, you can always call The Door Company at (614) 338-1414.]

A door sweep is an excellent way to prevent drafts and cold air from seeping in from underneath a door. Door sweeps can be as simple as a piece of rubber that is attached to the bottom of a door or as elaborate as an actual brush that not only prevents air from coming in from under the door, but also sweeps the area in front of the door as the door opens and closes.

Installing the Sweep:

Step 1

Purchase a door sweep that is the appropriate width for your door. Generally, door sweeps are the same width as the door. If you do not know the width of your door, then measure the door across.

Step 2

Using a power drill, attach the sweep to the bottom of the door. If you have a steel door, you will need to use a pre-drill holes with a bit designed for cutting into metal, or self-tapping screws.

Most door sweeps come with screws and holes already drilled into the sweep.

Step 3

Close the door and check to see that the sweep is preventing drafts and air from coming in under the door and that the door easily opens and closes.

If you need parts for this door sweep project, or any of the other projects we discuss in this series, give us a call at (614) 338-1414. Our headquarters at 3247 E. 11th Ave., Columbus, features a walk-in parts counter, and we can get you what you need!

Like The Door Company on Facebook,
follow @TheDoorCo_ofOH on Twitter,
or add us to your Google+ Circles.